NAME

tset, reset - establish or restore terminal characteristics

SYNOPSIS

tset [ -InQrs ] [ -ec ] [ -kc ] [ -m [port-ID
     [ baudrate] : type ] ... ] [type] reset [ - ] [ -ec ] [
-I ] [ -kc ] [ -n ]
     [ -Q ] [ -r ] [ -s ] [ -m [ indent ]
     [ test baudrate ]:  type ] ... [ type ]

DESCRIPTION

tset sets up your terminal, typically when you first log in. It does terminal dependent processing such as setting erase and kill characters, setting or resetting delays, sending any sequences needed to properly initialized the terminal, and the like. tset first determines the type of terminal involved, and then does necessary initializations and mode settings. If a port is not wired permanently to a specific terminal (not hardwired) it is given an appropriate generic identifier such as dialup. reset clears the terminal settings by turning off CBREAK and RAW modes, output delays and parity checking, turns on NEWLINE translation, echo and TAB expansion, and restores undefined special characters to their default state. It then sets the modes as usual, based on the terminal type (which will probably override some of the above). See stty(1) for more information. All arguments to tset may be used with reset. reset also uses rs= and rf= to reset the initialization string and file. This is useful after a program dies and leaves the terminal in a funny state. Often in this situation, characters will not echo as you type them. You may have to type `<LINEFEED>reset<LINEFEED>' since `<RETURN>' may not work. When no arguments are specified, tset reads the terminal type from the TERM environment variable and re-initializes the terminal, and performs initialization of mode, environment and other options at login time to determine the terminal type and set up terminal modes. When used in a startup script (.profile for sh(1) users or .login for csh(1) users) it is desirable to give information about the type of terminal you will usually use on ports that are not hardwired. Any of the alternate generic names given in /etc/termcap may be used for the identifier. Refer to the -m option below for more information. If no mapping applies and a final type option, not preceded by a -m, is given on the command line then that type is used. It is usually desirable to return the terminal type, as finally determined by tset, and information about the terminal's capabilities, to a shell's environment. This can be done using the -, -s, or -S options. For the Bourne shell, put this command in your .profile file:

eval `tset -s options...` or using the C shell, put this command in your .login file:

eval `tset -s options...` With the C shell, it is also convenient to make an alias in your .cshrc file:

alias tset 'eval `tset -s \!*`' This also allows the command:

tset 2621 to be invoked at any time to set the terminal and environment. It is not possible to get this aliasing effect with a Bourne shell script, because shell scripts cannot set the environment of their parent. If a process could set its parent's environment, none of this nonsense would be necessary in the first place. Once the terminal type is known, tset sets the terminal driver mode. This normally involves sending an initialization sequence to the terminal, setting the single character erase (and optionally the line-kill (full line erase)) characters, and setting special character delays. TAB and NEWLINE expansion are turned off during transmission of the terminal initialization sequence. On terminals that can backspace but not overstrike (such as a CRT), and when the erase character is `#', the erase character is changed as if -e had been used. The following options are available with tset:

- The name of the terminal finally decided upon is output on the standard output. This is intended to be captured by the shell and placed in the TERM environment variable.

-ec Set the erase character to be the named character c on all terminals. Default is the BACKSPACE key on the keyboard, usually ^H (CTRL-H). The character c can either be typed directly, or entered using the circumflex-character notation used here.

-ic Set the interrupt character to be the named character c on all terminals. Default is ^C (CTRL-C). The character c can either be typed directly, or entered using the circumflex-character notation used here.

-I Suppress transmitting terminal-initialization strings.

-kc Set the line kill character to be the named character c on all terminals. Default is ^U (CTRL-U). The kill character is left alone if -k is not specified. Control characters can be specified by prefixing the alphabetical character with a circumflex (as in CTRL-U) instead of entering the actual control key itself. This allows you to specify control keys that are currently assigned.

-n Specify that the new tty driver modes should be initialized for this terminal. Probably useless since stty new is the default.

-Q Suppress printing the `Erase set to' and `Kill set to' messages.

-r In addition to other actions, reports the terminal type.

-s   Output commands to set and export TERM.   This  can  be
     used with
          set noglob
          eval `tset -s ...`
          unset noglob

to bring the terminal information into the environment. Doing so makes programs such as vi(1) start up faster. If the SHELL environment variable ends with csh, C shell commands are output, otherwise Bourne shell commands are output.

-m [port-ID[baudrate]:type] ...
     Specify (map) a terminal type when connected to a  gen-
     eric  port  (such as dialup or plugboard) identified by
     port-ID.  The baudrate argument can be  used  to  check
     the  baudrate  of  the  port  and set the terminal type
     accordingly.  The target rate is prefixed by any combi-
     nation of the following operators to specify the condi-
     tions under which the mapping is made:
          >    Greater than
          @    Equals or ``at''
          <    Less than
          !    It is not the case that  (negates  the  above
               operators)
          ?    Prompt for the terminal type.  If no response
               is given, then type is selected by default.

In the following example, the terminal type is set to adm3a if the port is a dialup with a speed of greater than 300 or to dw2 if the port is a dialup at 300 baud or less. In the third case, the question mark preceding the terminal type indicates that the user is to verify the type desired. A NULL response indicates that the named type is correct. Otherwise, the user's response is taken to be the type desired.

tset -m 'dialup>300:adm3a' -m 'dialup:dw2' -m \
   'plugboard:?adm3a' To prevent interpretation as
metacharacters,  the  entire argument to -m should
be enclosed in single quotes.   When using  the  C
shell,  exclamation points should be preceded by a
backslash (\).

EXAMPLES

These examples all use the `-' option.   A  typical  use  of
tset  in  a  .profile  or .login will also use the -e and -k
options, and often the -n or  -Q  options  as  well.   These
options  have  been omitted here to keep the examples short.
To select a 2621, you might put the  following  sequence  of
commands  in  your .login file (or .profile for Bourne shell
users).
          set noglob
          eval `tset -s 2621`
          unset noglob
If you have a switch which connects to various ports (making
it  impractical  to identify which port you may be connected
to), and use various terminals from time to  time,  you  can
select  from among those terminals according to the speed or
baud rate.  In the example below, tset will prompt you for a
terminal  type  if  the baud rate is greater than 1200 (say,
9600 for a terminal connected by an RS-232 line), and use  a
Wyser 50 by default.  If the baud rate is less than or equal
to 1200, it will select a 2621.  Note the placement  of  the
question  mark,  and the quotes to protect the > and ?  from
interpretation by the shell.
          set noglob
          eval `tset -s -m 'switch>1200:?wy' -m 'switch<=1200:2621'`
          unset noglob
The following entry is appropriate if you  always  dial  up,
always  at  the  same  baud rate, on many different kinds of
terminals, and the terminal you use most often is an adm3a.
          set noglob
          eval `tset -s ?adm3a`
          unset noglob
If you want to make the selection based  only  on  the  baud
rate, you might use the following:
          set noglob
          eval `tset -s -m '>1200:wy' 2621`
          unset noglob
The following example quietly sets the  erase  character  to
BACKSPACE,  and  kill to CTRL-U. If the port is switched, it
selects a Concept 100 for speeds less than or equal to 1200,
and  asks  for  the  terminal type otherwise (the default in
this case is a Wyse 50).  If the port is a direct dialup, it
selects  Concept  100  as  the terminal type.  If logging in
over the ARPANET, the terminal type selected is a Datamediar
2500  terminal or emulator.  Note the backslash escaping the
NEWLINE at the end of the first line in the example.
          set noglob
          eval `tset -e -k^U -Q -s -m 'switch<=1200:concept100' -m \
               'switch:?wy' -m dialup:concept100 -m arpanet:dm2500`

          unset noglob

FILES

.login
.profile

SEE ALSO

csh(1),  sh(1),  vi(1),  stty(1)  in  the  User's  Reference
Manual.   ttytab(5),  termcap(5),  environ(5)  in the System
Administrator's Reference Manual.

NOTES

The tset command is one of the first commands a user must master when getting started on a UNIX system. Unfortunately, it is one of the most complex, largely because of the extra effort the user must go through to get the environment of the login shell set. Something needs to be done to make all this simpler, either the login program should do this stuff, or a default shell alias should be made, or a way to set the environment of the parent should exist. This program cannot intuit personal choices for erase, interrupt and line kill characters, so it leaves these set to the local system standards. It could well be argued that the shell should be responsible for ensuring that the terminal remains in a sane state; this would eliminate the need for the reset program.